Frequently Asked Questions
How Does the KlevaKlip Work?
KlevaKlip is a multi-board concealed fixing system, working on a "fixed pitch" principle, that provides consistent gapping of the boards. As each board is inserted into the KlevaKlip, it tightens the previous board, providing significant holding power of the board into the clip. This mechanical holding is supported by the use of adhesive (
Click Here >>>>for KlevaKlip Adhesive system information) to provide a look, longevity and feel that is difficult to obtain with conventional fastening systems.
What joist types are suitable for the KlevaKlip Saddle Clip?
Kiln dried Treated Pine or Hardwood, Laminated Veneer Lumber (LVL) 45-48mm in Width. If your joist is wider than 45-48mm we suggest to plane the joist down to this size. The Saddle Clip cannot be used on most metal joists RHS or C-Purlin as they are side fixed.
What Joist types are suitable for the KlevaKlip Top-Fix Clip?
Metal RHS, C Purlins, Kiln Dried (KD) Treated Pine or Kiln Dried (KD) Hardwoods. Non kiln dried joists, F14 unseasoned hardwoods and Laminated Veneer Lumber (LVL) joists are not to be used with the KlevaKlip KT series top-fix clips.
What size gap does the KlevaKlip provide between each of the Deck Boards?
Modwood Composites will provide a gap of around 4mm when using the KlevaKlips. This gap may vary over time in different climatic conditions.
What dimensions are the KlevaKlip's?
KT88 Top Fix Clips L 535mm x W 60mm
KS88 Saddle Clips L 535mm x W 48mm x H 25mm (Clip covers side of 45-48mm joist 25mm)
KT137 Top-Fix Clips L 568mm x W 60mm
KS137 Saddle Clips L 568mm x W 48mm x 25mm (Clip covers side of 45-48mm joist 25mm)
How do I calculate how many KlevaKlip's I will require for my deck?
There are three methods you can calculate your Klevaklip numbers or use the Modwood Decking Calculator
Click Here >>>>> that calculates how many Modwood deck boards, KlevaKlips, Adhesve & fasteners to be used on your deck
Per Square Meters (PSM)
Coverage 4. 5 KlevaKlip's = Approximately 1 Square Meter
Example: 20 Square Meter Deck X 4.5 = 90 KlevaKlip's
Square Meters of Deck Per Box of KlevaKlips
Top Fix Clips (40 Clips) 9 Square Meters
Saddle Clips (30 Clips) 6.5 Square Meters
Lineal Meters of decking boards
Total Lineal Meters divided by 11 x 4.5 KlevaKlips per Square Meter
Example: 300 Lineal Meters of Decking divided by 11 =27.27 X 4.5 =123 KlevaKlip's
What adhesive is recommended when fixing ModWood deck boards to the KlevaKlip's?
Bostik Zero Nails, Bostik No More Nails (Solvent based only) Fuller Toolbox.
*Bostik Zero Nails available only at Bunnings
Approved Adhesives For KlevaKlip
|
Board Type |
Approved Adhesives |
Modwood Natural Grain Collection Grooved Boards |
* Bostik Zero Nails, Bostik No More Nails Solvent Based only, Fuller Toolbox |
*Bostik Zero Nails available only at Bunnings
How much Adhesive will I need for my deck?
Standard 400g of Adhesive will cover approximately 4 Square meters of deck
Can Klevalip be used for screens?
Whereas it is quite common for privacy screens to have a gap between the boards of 12 - 20mm, the KlevaKlip system provides a maximum gap of just 4mm between boards. In a screening situation with the wind behind the screen, such a small gap can effectively cause the screen to act as a "sail". This can generate substantial pressures on the boards/screen - in very strong winds, this pressure can be in excess of 200kg/sqm.
Inserting boards into clips at height can be quite awkward, particularly without adequate manpower or stable footing. In a worst case scenario, this can cause significant "tearing" along the side of the board during insertion into the clip, thus significantly reducing the holding power of the clip.
Given the above information, KlevaKlip Systems P/L do not recommend the use of KlevaKlip products for screening when the screen is subject to wind velocity from behind the screen of greater than 40 km/hr, or when the screen is greater than 2.4m in height. In such instances "face fixing" of the product with screws or nails should be done.
Can Klevaklip be used in ceiling
situations
?
Due to the difficulties in fully supporting boards whilst they can correctly be inserted into a KlevaKlip, KlevaKlip Systems P/L does not recommend the use of KlevaKlip products in situations of ceilings and
soffits.
g
Can Klevalip be used for screens?
Whereas it is quite common for privacy screens to have a gap between the boards of 12 - 20mm, the KlevaKlip system provides a maximum gap of just 4mm between boards. In a screening situation with the wind behind the screen, such a small gap can effectively cause the screen to act as a "sail". This can generate substantial pressures on the boards/screen - in very strong winds, this pressure can be in excess of 200kg/sqm.
Inserting boards into clips at height can be quite awkward, particularly without adequate manpower or stable footing. In a worst case scenario, this can cause significant "tearing" along the side of the board during insertion into the clip, thus significantly reducing the holding power of the clip.
Given the above information, KlevaKlip Systems P/L do not recommend the use of KlevaKlip products for screening when the screen is subject to wind velocity from behind the screen of greater than 40 km/hr, or when the screen is greater than 2.4m in height. In such instances "face fixing" of the product with screws or nails should be done.
Can Klevaklip be used in ceiling
situations
?
Due to the difficulties in fully supporting boards whilst they can correctly be inserted into a KlevaKlip, KlevaKlip Systems P/L does not recommend the use of KlevaKlip products in situations of ceilings and soffits.
Can I fix the KlevaKlip
KT series Top Fix clip directly fixed to concrete or tiled
areas?
No, KlevaKlip KT Series cannot be directly fixed to concrete or tiled surfaces. Battens made from Treated Pine, Steel or aluminium with an absolute minimum of 50mm in height and approximately 50mm in width can be fixed to the concrete or tiled surface to aid ventilation to your deck and substructure. Battens should run in the direction of the fall of the concrete or tiled surface. Avoid closing in any sides or ends of your deck to aid further ventilation.
Are stainless Steel Clips available for Coastal or Salt water Pool areas?
Yes, only the Top Fix Clips are available - Saddle clips are not available in Stainless Steel
What type of clips can I use around swimming pool areas?
Only Stainless Steel clips can be used.
Please
Click Here
>>>for Corrosion Resistance Document
What areas should I use Stainless Steel and Galvanised KlevaKlips ?
Please
Click
Here >>>
for Corrosion Resistance Document
When using137mm x 32mm Modwood Marina Board Natural Grain Collection what type of KlevaKlip can I use?
The KT137S Stainless Steel clip will suit.
Can I use the KlevaKlip KT series Top Fix clip directly on to timber joists?
Although the KlevaKlip side fixed KS series Saddle clip is designed for Timber joists the KlevaKlip KT series Top Fix clip can also be utilised for timber joists. KT series KlevaKlip's cannot be used with Laminated Veneer Lumber joists (LVL) or F14 unseasoned Hardwoods.
Can I use rubber joist liners on the KlevaKlip System?
Yes, the KlevaKlip saddle clip was designed to be used in conjunction with a rubber joist liner.It is suggested that rubber joist liners can used with Laminated Veneer Lumbers (LVL)
What Joist centres does KlevaKlip require?
KlevaKlip should be used as per joist centres recommended for the deck board you are fixing.
What Box quantities are the KlevaKlip's packaged?
KlevaKlip Saddle Clips Boxes 30
Klevaklip Top-Fix Clips Boxes 40
What are the weights and dimensions of the KlevaKlip Saddle and Top-Fix boxes?
KlevaKlip Saddle Clips: KS88 56cm x 25cm x 16cm 13kg
KS137 85cm x 25cm x16cm
KlevaKlip Top-Fix Clips: KT88 56cm x 25cm x 16cm 10kg
KT137 85cm x 25cm x16cm
Can I use Klevaklip on mitre joints?
No, Klevaklip is not designed to use with Mitre joints.
Can Treated Pine deck boards be used with the KlevaKlip System?
Treated Pine deck boards are not suitable for use with the KlevaKlip system due to expansion of the pine when wet and contraction when dry.
What is the thickness of the material used in the Klevalip's?
G-300 Z600 Galvanised .95
304 Stainless Steel .90
What height are the Klevaklips?
The thickness of the metal is 1mm and the nipples are around 2mm in height= Total 3mm
|
